Blog
Non-Magnetic Stainless Steel for Medical Devices & Surgical Instruments

Medical devices and surgical instruments demand materials that meet the highest standards of biocompatibility, corrosion resistance, sterilization durability, and mechanical performance. Among the many materials used in medical manufacturing, non-magnetic austenitic stainless steel — particularly 316L and its premium variant 316LVM — is the dominant choice for a vast range of applications, from surgical forceps and scalpels to orthopedic implants and MRI-compatible equipment. The non-magnetic property is not merely a convenience; in many medical contexts, it is a critical safety requirement.
This article explores why non-magnetic stainless steel is essential in medical devices, identifies the key grades used, explains the difference between standard 316L and vacuum-melted 316LVM, reviews regulatory requirements (FDA, ISO 13485, ISO 10993), and provides practical guidance for sourcing medical-grade non-magnetic stainless steel. For a broader understanding of non-magnetic stainless steel metallurgy, crystal structure, and grade selection, refer to our Non-Magnetic Stainless Steel: The Definitive Guide and our detailed grade comparison of 304 vs 316 vs 310 vs 321 vs 904L.
Key point: Non-magnetic austenitic stainless steel (primarily 316L and 316LVM) is the material of choice for medical devices and surgical instruments because it offers excellent biocompatibility, corrosion resistance, sterilization durability, and — critically — zero magnetic interference, which is essential for MRI compatibility and electromagnetic surgical navigation systems. Fullgreat supplies medical-grade non-magnetic stainless steel in strip, wire, bar, and sheet forms with certified low magnetic permeability and full material traceability.
Why Non-Magnetic Matters in Medical Devices
The non-magnetic property of austenitic stainless steel is not just a technical specification — it directly impacts patient safety, diagnostic accuracy, and equipment functionality in several critical medical contexts:
1. MRI Compatibility
Magnetic Resonance Imaging (MRI) machines generate extremely powerful static magnetic fields, typically ranging from 1.5 Tesla to 7 Tesla (and up to 10.5 Tesla in research systems). Any ferromagnetic material brought into the MRI suite can become a dangerous projectile, attracted to the magnet with lethal force. In addition, ferromagnetic implants or instruments can cause image artifacts (signal voids and distortions) that compromise diagnostic quality, and they can heat up due to radiofrequency fields, potentially causing tissue burns.
Non-magnetic austenitic stainless steel (μr < 1.01) is considered MRI-safe or MRI-conditional under most conditions. Surgical instruments, implants, and equipment components made from 316L or 316LVM can be used in and around MRI scanners without the projectile risk or image artifacts associated with ferromagnetic materials like carbon steel, ferritic stainless steel (430), or martensitic stainless steel (410, 420).
2. Electromagnetic Surgical Navigation
Modern surgical navigation systems use electromagnetic fields to track the position and orientation of surgical instruments in real time, overlaying instrument position on pre-operative CT or MRI scans. These systems are widely used in neurosurgery, orthopedic surgery, ENT procedures, and interventional radiology. Ferromagnetic instruments can distort the electromagnetic field, causing tracking errors that compromise surgical accuracy. Non-magnetic stainless steel instruments ensure that the electromagnetic tracking system operates with maximum precision.
3. Implant Safety
For implanted devices (orthopedic plates, screws, pins, vascular stents, dental implants), the non-magnetic property is important for two reasons. First, patients with implants may need MRI scans during their lifetime, and non-magnetic implants are MRI-safe (or MRI-conditional with specific conditions). Ferromagnetic implants can experience torque and displacement forces in the MRI scanner, potentially causing tissue damage or implant migration. Second, non-magnetic implants do not interfere with electromagnetic diagnostic equipment (such as magnetoencephalography, MEG) that the patient may undergo.
4. Electronic Medical Equipment
Many medical devices contain sensitive electronic components — patient monitors, infusion pumps, defibrillators, diagnostic analyzers, and robotic surgical systems. Ferromagnetic materials in the device housing or internal components can interfere with electromagnetic shielding, cause unwanted magnetic coupling, or generate electromagnetic interference (EMI) that affects device performance. Non-magnetic stainless steel enclosures and components ensure that electronic medical equipment operates reliably without electromagnetic interference.
For decorative or conductive hardware in medical equipment where a copper finish is required, copper clad non-magnetic stainless steel (FPD726) offers a non-magnetic, copper-surfaced alternative.
5. Sterilization Equipment
Autoclaves, plasma sterilizers, and ultrasonic cleaning equipment often use magnetic fields or induction heating. Non-magnetic stainless steel instrument trays and containers ensure that the sterilization process is not affected by magnetic interactions, and they prevent instruments from sticking to magnetic surfaces during automated handling.
Key Non-Magnetic Stainless Steel Grades for Medical Applications
Several grades of non-magnetic austenitic stainless steel are used in medical device manufacturing. The choice depends on the specific application (instrument vs. implant vs. equipment), the required mechanical properties, corrosion resistance, and the level of biocompatibility certification needed.
| Grade | EN Number | Key Alloying | Magnetic Permeability (μr) | Primary Medical Uses |
|---|---|---|---|---|
| 316L | 1.4404 | 17% Cr, 11% Ni, 2.5% Mo, ≤0.030% C | 1.003 – 1.008 | Surgical instruments, orthopedic implants (temporary), dental instruments, pharmaceutical equipment, MRI-compatible hardware |
| 316LVM | 1.4441 | 17% Cr, 13% Ni, 2.5% Mo, ≤0.030% C, vacuum-melted | 1.002 – 1.005 | Permanent implants (orthopedic, cardiovascular), premium surgical instruments, implantable devices, high-reliability medical components |
| 304 / 304L | 1.4301 / 1.4307 | 18% Cr, 8% Ni, ≤0.030% C (304L) | 1.003 – 1.01 | Medical equipment housings, hospital furniture, sterilization trays, non-implant instruments, laboratory equipment (lower cost alternative to 316L) |
| 302 | 1.4300 | 18% Cr, 8% Ni, ≤0.15% C | 1.003 – 1.01 | Surgical wire, springs, suture wire, small instrument components (higher carbon for strength, but less corrosion-resistant than 316L) |
| 310 / 310S | 1.4845 | 25% Cr, 20% Ni, ≤0.08% C (310S) | 1.002 – 1.005 | High-temperature medical equipment, furnace components, heat treatment fixtures for implant manufacturing (excellent high-temperature stability and very low magnetic permeability) |
Important note: Not all “surgical stainless steel” is non-magnetic. Martensitic grades such as 420 (1.4021) and 440A (1.4109) are widely used for cutting instruments (scalpels, scissors, osteotomes) because they can be hardened to high hardness for sharp cutting edges. However, these martensitic grades are ferromagnetic and are NOT MRI-safe. They are suitable for hand-held cutting instruments that are removed from the patient before imaging, but they should never be used for implants or for instruments that may be used in or near MRI scanners. Always verify the grade and magnetic properties when sourcing surgical instruments.
316L vs 316LVM: What’s the Difference?
316L and 316LVM are the two most important non-magnetic stainless steel grades for medical implants and premium surgical instruments. While they have similar chemical compositions, the difference in melting process results in significant differences in cleanliness, microstructure, and performance.
Melting Process
- 316L: Typically produced by conventional electric arc furnace (EAF) or argon oxygen decarburization (AOD) melting. This is the standard industrial melting process used for most stainless steel production.
- 316LVM: Produced by vacuum induction melting (VIM), often followed by vacuum arc remelting (VAR) for the highest quality. The vacuum environment removes dissolved gases (hydrogen, oxygen, nitrogen) and reduces non-metallic inclusions.
Key Differences
| Property | 316L (standard) | 316LVM (vacuum-melted) |
|---|---|---|
| Melting process | EAF / AOD (air-melted) | VIM / VAR (vacuum-melted) |
| Inclusion content | Standard (some non-metallic inclusions present) | Ultra-low (vacuum removes inclusions and dissolved gases) |
| Microstructure uniformity | Good | Excellent (very uniform, minimal segregation) |
| Mechanical properties | Meet ASTM F138 / F139 minimums | Exceed minimums with tighter consistency; higher fatigue resistance |
| Corrosion resistance | Excellent | Superior (fewer inclusions = fewer corrosion initiation sites) |
| Fatigue life | Good | Excellent (inclusions are fatigue crack initiation sites; fewer inclusions = longer fatigue life) |
| Magnetic permeability (μr) | 1.003 – 1.008 | 1.002 – 1.005 (lower and more consistent) |
| Biocompatibility | Meets ISO 10993 | Meets ISO 10993 with superior performance (fewer inclusions = less risk of adverse tissue reaction) |
| Cost | Lower | Higher (typically 2-3× the cost of standard 316L) |
| Standards | ASTM F138, F139, ISO 5832-1 | ASTM F138, F139, ISO 5832-1 (with VIM/VAR requirement) |
When to Use Which
- Use 316L for: Surgical instruments (non-implant), dental instruments, pharmaceutical equipment, MRI-compatible hardware, medical device housings, sterilization equipment, temporary implants (short-term fixation devices removed after healing).
- Use 316LVM for: Permanent implants (orthopedic plates, screws, pins that remain in the body), cardiovascular stents and implantable devices, premium surgical instruments subject to high fatigue loads, any implantable device where long-term reliability and biocompatibility are critical.
We have published a detailed deep-dive on 316L stainless steel strip covering specifications, properties, and sourcing considerations for strip products, many of which apply to medical-grade strip and wire as well.
Medical Device Applications of Non-Magnetic Stainless Steel
Surgical Instruments
Non-magnetic 316L stainless steel is the standard material for a vast range of surgical instruments, including forceps, hemostats, needle holders, retractors, clamps, scissors (non-cutting), probes, curettes, and orthopedic instruments. The non-magnetic property ensures that these instruments can be used in operating rooms equipped with electromagnetic navigation systems and that they are safe for use in and around MRI scanners. 316L offers excellent corrosion resistance to repeated sterilization cycles (autoclaving, ethylene oxide, plasma), good mechanical strength, and the ability to be passivated and electropolished for a smooth, cleanable surface.
For cutting instruments (scalpels, scissors, osteotomes, chisels), martensitic grades (420, 440A) are typically used because they can be hardened to high hardness for sharp, durable cutting edges. However, as noted above, these are ferromagnetic and not MRI-safe. Some manufacturers offer “MRI-safe” cutting instruments made from precipitation-hardening grades or ceramic coatings, but these are specialized products.
Orthopedic Implants
316L and 316LVM are widely used for orthopedic implants, including bone plates, screws, pins, wires, intramedullary nails, and joint replacement components. While titanium and cobalt-chromium alloys have become more common for permanent weight-bearing implants in recent decades, stainless steel remains an important material due to its excellent mechanical properties, fatigue resistance, and lower cost. 316LVM (vacuum-melted) is preferred for permanent implants due to its superior cleanliness and fatigue life. The non-magnetic property ensures that patients with stainless steel implants can safely undergo MRI scans.
Orthopedic implants made from 316L/316LVM must meet strict standards including ASTM F138 (for wrought 316L) and ISO 5832-1. The material must be supplied with full material traceability (heat number, batch number) and certified mechanical and corrosion test results. We explain how to verify these results in our comprehensive guide to Mill Test Certificates (EN 10204 3.1).
Cardiovascular and Endovascular Devices
316LVM is the traditional material for coronary stents and other endovascular devices, although cobalt-chromium and platinum-chromium alloys have become more common in recent years due to their higher radiopacity and thinner strut capability. 316LVM is still used for some stent platforms, as well as for guidewires, catheters, and implantable cardiac devices (pacemaker leads, defibrillator components). The non-magnetic property is critical for cardiovascular implants because patients with these devices frequently require MRI scans, and the devices must be MRI-conditional or MRI-safe.
Dental Instruments and Implants
316L stainless steel is widely used for dental instruments (mirrors, probes, scalers, forceps, elevators) and for some dental implants and orthodontic appliances (archwires, brackets, bands). The non-magnetic property is important for dental instruments used in practices equipped with cone-beam CT (CBCT) and other imaging equipment. For dental implants, titanium is more common due to its superior osseointegration, but 316L/316LVM is still used for some implant components and orthodontic appliances.
MRI-Compatible Equipment and Hardware
MRI suites require a vast range of non-magnetic equipment and hardware, including patient tables, coil holders, monitoring equipment, anesthesia equipment, IV poles, surgical tables, and fasteners (screws, bolts, nuts). Non-magnetic 316L stainless steel is the standard material for these applications because it is MRI-safe, corrosion-resistant, and mechanically robust. Even small ferromagnetic components (such as a steel screw in an IV pole) can become a dangerous projectile in the MRI suite, so every component must be verified as non-magnetic.
Pharmaceutical and Biotechnology Equipment
316L stainless steel is the gold standard for pharmaceutical and biotechnology manufacturing equipment, including reactors, fermenters, piping systems, valves, pumps, heat exchangers, and storage tanks. The non-magnetic property is important for equipment used in biopharmaceutical manufacturing because many bioprocesses involve magnetic mixing, magnetic separation, or electromagnetic sensing. 316L offers excellent corrosion resistance to pharmaceutical chemicals, cleanability (CIP/SIP compatibility), and biocompatibility. The surface finish is typically electropolished to Ra < 0.5 μm for pharmaceutical applications.
Laboratory and Diagnostic Equipment
Non-magnetic 316L stainless steel is used for laboratory equipment, analytical instruments, diagnostic analyzers, and sample handling systems. The non-magnetic property ensures that the equipment does not interfere with magnetic separation techniques (used in molecular biology and immunology), mass spectrometry, or other sensitive analytical methods. 316L also offers excellent corrosion resistance to laboratory chemicals and cleanability for sterile environments.
Regulatory Requirements and Standards
Medical devices are among the most heavily regulated products in the world. Manufacturers must comply with strict regulatory requirements in every market where they sell their devices. The following are the key standards and regulations relevant to non-magnetic stainless steel for medical devices:
Material Standards
| Standard | Title | Scope |
|---|---|---|
| ASTM F138 | Standard Specification for Wrought 316L Stainless Steel Bar and Wire for Surgical Implants (UNS S31673) | The primary material standard for 316L stainless steel used in surgical implants. Specifies chemical composition, mechanical properties, microstructure, and test methods. |
| ASTM F139 | Standard Specification for Wrought 316L Stainless Steel Sheet and Strip for Surgical Implants (UNS S31673) | Material standard for 316L stainless steel sheet and strip used in surgical implants. |
| ISO 5832-1 | Implants for surgery — Metallic materials — Part 1: Wrought stainless steel | International standard for wrought stainless steel for surgical implants. Equivalent to ASTM F138/F139 in many respects. |
| ASTM A270 | Standard Specification for Seamless and Welded Austenitic Stainless Steel Sanitary Tubing | Standard for sanitary tubing used in pharmaceutical and food processing (not implant-specific, but relevant for medical equipment). |
| ASME BPE | Bioprocessing Equipment Standard | Standard for biopharmaceutical processing equipment, including material requirements and surface finish specifications. |
Biocompatibility Standards
| Standard | Title | Scope |
|---|---|---|
| ISO 10993-1 | Biological evaluation of medical devices — Part 1: Evaluation and testing within a risk management process | The overarching standard for biocompatibility evaluation of medical devices. Defines the framework for assessing biological response to device materials. |
| ISO 10993-5 | Tests for in vitro cytotoxicity | Specifies test methods for evaluating the cytotoxicity of medical device materials (including stainless steel). |
| ISO 10993-6 | Tests for local effects after implantation | Specifies test methods for evaluating the local tissue response to implanted materials. |
| ISO 10993-10 | Tests for skin sensitization | Specifies test methods for evaluating the skin sensitization potential of medical device materials. |
| ISO 10993-15 | Identification and quantification of degradation products from metals and alloys | Specifies methods for identifying and quantifying metal ions released from metallic medical devices (important for corrosion and biocompatibility assessment). |
Quality Management Systems
- ISO 13485: Medical devices — Quality management systems — Requirements for regulatory purposes. This is the primary QMS standard for medical device manufacturers. Suppliers of medical-grade materials should be ISO 13485 certified or operate under a quality system that meets medical device requirements.
- 21 CFR Part 820 (FDA QSR): US FDA Quality System Regulation for medical devices. Equivalent in many respects to ISO 13485. Manufacturers selling medical devices in the US must comply with this regulation.
- EU MDR (2017/745): European Union Medical Device Regulation. Replaces the previous MDD (93/42/EEC) and imposes stricter requirements on medical device manufacturers, including material traceability and post-market surveillance.
MRI Safety Standards
- ASTM F2503: Standard Practice for Marking Medical Devices and Other Items for Safety in the Magnetic Resonance Environment. Defines the labeling requirements for MRI-safe, MRI-conditional, and MRI-unsafe devices.
- ISO/TS 10974: Assessment of the safety of medical devices intended for use in the magnetic resonance environment. Provides guidance for testing and evaluating the safety of medical devices in MRI environments.
Surface Finish Requirements for Medical-Grade Stainless Steel
The surface finish of medical-grade stainless steel is critical for biocompatibility, corrosion resistance, cleanability, and sterilization. The following surface finishes are commonly specified for medical applications:
| Surface Finish | Typical Ra (μm) | Process | Medical Applications |
|---|---|---|---|
| Mill finish (2B) | 0.5 – 1.0 | Cold rolling + bright annealing + pickling | General medical equipment, non-critical components, base material for further finishing |
| Bright annealed (BA) | 0.2 – 0.5 | Cold rolling + bright annealing in protective atmosphere | Surgical instruments, medical device components, aesthetic parts |
| Mechanical polish | 0.1 – 0.4 | Abrasive belt polishing + buffing | Surgical instruments, hand-held devices, visible surfaces |
| Electropolish | 0.1 – 0.3 | Electrochemical polishing (anodic dissolution) | Implants, pharmaceutical equipment, food-contact surfaces, critical cleanable surfaces (removes surface contaminants, improves corrosion resistance, creates smooth, non-porous surface) |
| Passivation | No change to Ra | Chemical treatment (citric or nitric acid) to remove free iron and restore chromium oxide layer | All medical-grade stainless steel components after machining/fabrication (standard post-processing step, not a surface finish per se) |
| Ultra-polish (mirror) | < 0.05 | Multi-stage mechanical polishing + electropolishing | Premium surgical instruments, implantable devices, high-end medical equipment (specialized, high-cost finish) |
Passivation is a critical post-fabrication step for all medical-grade stainless steel components. During machining, forming, and handling, free iron particles can become embedded in the stainless steel surface. These iron particles can rust and initiate corrosion, compromising the component’s performance and biocompatibility. Passivation uses citric acid or nitric acid to dissolve the free iron particles without attacking the stainless steel base material, restoring the protective chromium oxide passive layer. ASTM A967 is the standard specification for chemical passivation of stainless steel parts.
Electropolishing is often specified for implants and pharmaceutical equipment because it offers several advantages over mechanical polishing: it removes a thin layer of surface material (including embedded contaminants and burrs), creates a smooth, non-porous surface that is easier to clean and sterilize, improves corrosion resistance by enriching the chromium content at the surface, and produces a uniform finish regardless of part geometry (mechanical polishing cannot reach internal cavities and complex geometries). ASME BPE specifies electropolished surfaces (Ra < 0.5 μm, typically Ra < 0.38 μm) for biopharmaceutical equipment.
Testing and Certification for Medical-Grade Stainless Steel
Medical-grade stainless steel must undergo rigorous testing and certification to ensure that it meets all applicable standards and is safe for its intended use. The following tests are commonly required:
Chemical Analysis
Full chemical composition analysis by optical emission spectrometry (OES) or combustion analysis, verifying that all elements are within the specification limits (e.g., ASTM F138). For implant-grade material, the analysis must include all elements specified in the standard, with no omissions.
Mechanical Testing
- Tensile test: Tensile strength, yield strength, and elongation (per ASTM E8 / EN ISO 6892). Must meet minimum requirements specified in the material standard.
- Hardness test: Rockwell or Vickers hardness, as specified.
- Fatigue test: For implant-grade material, fatigue testing may be required to verify fatigue life under cyclic loading conditions.
Corrosion Testing
- Pitting corrosion test: ASTM G48 (ferric chloride test) or ASTM F746 (cyclic potentiodynamic polarization test) to verify pitting corrosion resistance.
- Intergranular corrosion test: ASTM A262 (Practice E, Strauss test) to verify resistance to intergranular corrosion after sensitization.
- Stress corrosion cracking test: For specific applications, SCC testing may be required.
Microstructure and Inclusion Analysis
- Microstructure examination: Verify fully austenitic microstructure with no detrimental phases (sigma, chi, carbides). ASTM E112 for grain size.
- Inclusion rating: For 316LVM and implant-grade material, non-metallic inclusion rating per ASTM E45 or DIN 50602. Vacuum-melted material should have very low inclusion content.
Magnetic Permeability Testing
For non-magnetic medical applications, magnetic permeability testing per ASTM A342 or using a feritscope/magnetic permeability meter, verifying that μr meets the specified requirement (typically < 1.01 for general medical, < 1.005 for premium implant and MRI-critical applications).
Biocompatibility Testing
Per ISO 10993, as applicable to the device type and contact duration. This may include cytotoxicity (ISO 10993-5), sensitization (ISO 10993-10), implantation (ISO 10993-6), and other tests as determined by the biocompatibility risk assessment.
Certification
Every batch of medical-grade stainless steel should be supplied with an EN 10204 Type 3.1 (or Type 3.2 for critical implants) Mill Test Certificate documenting all test results, heat number, batch number, and material specification. For implant applications, full material traceability from melt to finished device is required by regulators.
Common Mistakes in Medical-Grade Stainless Steel Sourcing
Mistake 1: Assuming “surgical stainless steel” means 316L
The term “surgical stainless steel” is not a standardized material designation. It can refer to 316L, 316LVM, 304, 420, 440A, or other grades, depending on the application and manufacturer. When sourcing medical-grade stainless steel, always specify the exact grade (e.g., “316L per ASTM F138”) rather than using the vague term “surgical stainless steel.”
Mistake 2: Using standard 316L for permanent implants
Standard air-melted 316L (ASTM F138) is acceptable for many medical applications, including surgical instruments and temporary implants. However, for permanent implants (devices that remain in the body long-term), 316LVM (vacuum-melted) is strongly preferred due to its superior cleanliness, lower inclusion content, and better fatigue resistance. Using standard 316L for permanent implants may increase the risk of fatigue failure and adverse tissue reactions. Always consult the applicable regulatory requirements and your materials engineer when selecting implant-grade material.
Mistake 3: Neglecting to verify non-magnetic properties
Even austenitic stainless steel can become partially magnetic after cold working (strain-induced martensite), as explained in our definitive guide to non-magnetic stainless steel. When sourcing medical-grade stainless steel for MRI-critical or electromagnetic navigation applications, always specify the maximum magnetic permeability requirement on the purchase order and require the supplier to include permeability test results on the Mill Test Certificate. Do not assume that “316L” automatically means “non-magnetic” — verify it.
Mistake 4: Skipping passivation after fabrication
Stainless steel components that have been machined, formed, welded, or handled must be passivated before use in medical applications. Free iron particles embedded during fabrication can cause rusting and corrosion, compromising the component’s performance and biocompatibility. Passivation (per ASTM A967) is a simple, low-cost step that should never be skipped for medical-grade stainless steel components.
Mistake 5: Ignoring surface finish requirements
The surface finish of medical-grade stainless steel directly affects cleanability, sterilization, corrosion resistance, and biocompatibility. Always specify the required surface finish (Ra value and process) on the purchase order and drawings. For implants and pharmaceutical equipment, electropolishing is typically required. For surgical instruments, a mechanical polish or electropolish may be specified, depending on the instrument type. Do not assume that the supplier will provide the correct finish — specify it explicitly.
Mistake 6: Not requiring full material traceability
Medical device regulations (FDA QSR, EU MDR, ISO 13485) require full material traceability from the raw material melt to the finished device. When sourcing medical-grade stainless steel, always require the supplier to provide the heat number, batch number, and material certification for every shipment. Maintain records of this traceability information for the lifetime of the device (and beyond, as required by applicable regulations). In the event of a material-related issue or recall, traceability is essential for identifying affected devices and implementing corrective actions.
Fullgreat’s Medical-Grade Non-Magnetic Stainless Steel Capability
Fullgreat Metal supplies medical-grade non-magnetic stainless steel in a wide range of grades, forms, and dimensions for medical device and surgical instrument manufacturers. Our capabilities include:
| Capability | Details |
|---|---|
| Available grades | 304, 304L, 316, 316L, 316LVM (VIM/VAR), 302, 310, 310S, 321, 904L |
| Product forms | Strip, coil, sheet, plate, bar, wire, flat wire, tube, custom profiles |
| Strip dimensions | Thickness: 0.05 – 6.0 mm; Width: 3 – 600 mm (precision slitting to custom widths) |
| Wire dimensions | Diameter: 0.1 – 12 mm (straight or coil); Round, flat, square, and custom shapes |
| Bar dimensions | Diameter: 3 – 200 mm; Length: up to 6000 mm; Round, hex, square, flat |
| Heat treatment | Solution annealed (standard), bright annealed, stress relieved, custom tempers |
| Surface finishes | 2B, BA, No.4, 2K, 4K, 6K, 8K (mirror), hairline, mechanical polish, electropolish (via qualified partners), passivation |
| Magnetic permeability | Standard: μr < 1.01 (annealed); Low-permeability: μr < 1.005 available (316LVM, 310, 904L); Permeability test results on MTC |
| Material standards | ASTM F138, F139, A240, A270, A666; ISO 5832-1; EN 10088, EN 10204 3.1/3.2 |
| Testing | Chemical analysis (OES), tensile, hardness, corrosion (pitting, intergranular), microstructure, inclusion rating, magnetic permeability, eddy current, ultrasonic |
| Certification | EN 10204 Type 3.1 MTC standard; Type 3.2 (third-party: SGS, TÜV, BV) available; Full heat and batch traceability; ISO 9001:2015 certified |
| Custom processing | Precision slitting, cut-to-length, edge rounding, deburring, leveling, shearing, laser cutting, waterjet cutting, CNC machining, passivation |
| Minimum order | Trial orders and sample quantities available for prototype development; volume production with monthly supply contracts |
Our medical-grade stainless steel is used by manufacturers of surgical instruments, orthopedic implants, dental instruments, MRI-compatible equipment, pharmaceutical processing systems, and laboratory and diagnostic devices worldwide. We work closely with medical device manufacturers to specify the optimal grade, heat treatment, surface finish, and magnetic permeability for each application. For implant-grade applications, we can supply 316LVM (VIM/VAR) with ultra-low inclusion content and full material traceability. We also offer magnetic permeability testing and can include permeability results on the Mill Test Certificate for MRI-critical applications.
For stainless steel strip products used in medical device manufacturing (such as surgical instrument blanks, implant components, and medical device housings), the cold rolling reduction ratio affects both mechanical properties and magnetic stability. We can recommend the optimal combination of grade, reduction ratio, and annealing to meet your magnetic permeability and mechanical property requirements.
Frequently Asked Questions
Q: Is 316L stainless steel MRI-safe?
A: Yes, fully annealed 316L stainless steel is non-magnetic (paramagnetic, μr < 1.01) and is generally considered MRI-safe or MRI-conditional. It will not experience significant projectile forces, torque, or heating in MRI scanners under most conditions. However, if the 316L has been cold-worked (which can induce martensite and partial magnetism), or if it is a complex implant device with specific geometry, MRI safety should be evaluated per ASTM F2503 and ISO/TS 10974. Always verify the magnetic properties of the specific material and device before use in MRI environments. For premium MRI-critical applications, 316LVM (μr < 1.005) is preferred.
Q: What is the difference between 316L and surgical stainless steel?
A: “Surgical stainless steel” is a non-standard, generic term that can refer to several different grades, including 316L, 316LVM, 304, 420, and 440A. 316L is a specific austenitic stainless steel grade (UNS S31603, EN 1.4404) with defined chemical composition (16-18.5% Cr, 10-14% Ni, 2-3% Mo, ≤0.030% C). When sourcing medical-grade material, always specify the exact grade and applicable standard (e.g., “316L per ASTM F138”) rather than using the vague term “surgical stainless steel.”
Q: Can 316L stainless steel be used for permanent implants?
A: Standard 316L (ASTM F138) can be used for some permanent implant applications, but 316LVM (vacuum-melted) is generally preferred for permanent implants due to its superior cleanliness, lower inclusion content, better fatigue resistance, and more consistent magnetic permeability. The choice between 316L and 316LVM depends on the specific implant type, loading conditions, and regulatory requirements. In recent decades, titanium and cobalt-chromium alloys have become more common for many permanent implant applications (especially weight-bearing joints), but 316L/316LVM remains an important material for orthopedic fixation devices, cardiovascular devices, and other implants. Always consult a qualified materials engineer and the applicable regulatory standards when selecting implant material.
Q: Is 304 stainless steel suitable for medical devices?
A: 304 (and 304L) austenitic stainless steel is non-magnetic and can be used for certain medical device applications, particularly non-implant applications such as medical equipment housings, hospital furniture, sterilization trays, laboratory equipment, and some non-critical surgical instruments. However, 304 has lower corrosion resistance than 316L (no molybdenum), which makes it less suitable for implants, surgical instruments subject to repeated sterilization, or applications involving bodily fluids or chloride-containing solutions. For most implant and surgical instrument applications, 316L or 316LVM is the preferred material. 304 is a cost-effective choice for non-critical, non-implant medical equipment where corrosion exposure is mild.
Q: How do I verify that medical-grade stainless steel is non-magnetic?
A: There are several methods to verify non-magnetic properties, depending on the required precision: (1) Permanent magnet test — a simple qualitative test; if the magnet is not attracted, the material is likely fully austenitic and non-magnetic. (2) Magnetic permeability meter / feritscope — a quantitative instrument that measures relative permeability (μr); suitable for verifying that μr meets a specified limit (e.g., < 1.01 or < 1.005). (3) Mill Test Certificate — the supplier’s certification should include magnetic permeability test results if specified on the purchase order. For medical and MRI-critical applications, always specify the maximum magnetic permeability requirement on the purchase order and require quantitative test results on the MTC, not just a magnet test.
Q: What surface finish is required for medical implants?
A: The required surface finish depends on the specific implant type and application. For orthopedic implants (plates, screws, pins), the surface finish is typically specified per the applicable material standard (ASTM F138) and may range from mill finish to mechanically polished, depending on the component. For cardiovascular stents and implantable devices, electropolishing is commonly specified to produce a smooth, clean surface with minimal inclusions. For dental implants, a roughened surface (sandblasted, acid-etched) is often specified to promote osseointegration — this is a specialized surface treatment, not a standard stainless steel finish. Always consult the applicable regulatory standards and your materials engineer when specifying implant surface finishes. For pharmaceutical equipment, ASME BPE specifies electropolished surfaces (Ra < 0.5 μm, typically Ra < 0.38 μm).
Q: Do I need ISO 13485 certification to supply medical-grade stainless steel?
A: ISO 13485 certification is not strictly required for raw material suppliers, but it is highly preferred and often required by medical device manufacturers as a condition of supplier approval. ISO 13485 is a quality management system standard specifically for medical devices, and it demonstrates that the supplier has implemented a quality system that meets medical device regulatory requirements. Many medical device manufacturers will only source materials from ISO 13485-certified suppliers, or they will require the supplier to undergo a rigorous supplier audit to verify that their quality system meets medical device requirements. At minimum, suppliers of medical-grade stainless steel should be ISO 9001 certified and should be able to demonstrate full material traceability, documented quality procedures, and compliance with applicable material standards (ASTM F138, ISO 5832-1, etc.).
Need non-magnetic medical-grade stainless steel for your device or instrument? Fullgreat supplies 316L, 316LVM (VIM/VAR), 304L, 310, and other austenitic grades in strip, wire, bar, sheet, and custom forms with certified low magnetic permeability (μr < 1.01, < 1.005 available), full material traceability, and EN 10204 3.1/3.2 certification. Surface finishes including electropolish and passivation available. Request a quote → or contact our medical materials team at Bruce@fullgreat.com for grade selection support and sample material.
