Blog
Aluminum Strip for EV Battery Busbars: 1060/1070/3003 Alloy Selection & Conductivity

Why Aluminum for EV Battery Busbars?
Electric vehicle (EV) battery packs need busbars to carry large currents between battery cells, modules, and the inverter. These busbars handle hundreds of amps. Therefore, material selection is critical. Copper has long been the traditional choice for busbars due to its high conductivity. However, in recent years, aluminum has rapidly become the preferred material for EV battery busbars. Why? The answer comes down to three factors: weight, cost, and sufficient conductivity.
Aluminum weighs roughly one-third of copper. In an EV, every kilogram saved directly improves range. A typical EV battery pack contains 10–30 meters of busbar material. Switching from copper to aluminum can reduce busbar weight by 40–60%. This weight saving translates directly into longer driving range or a smaller, lighter battery pack.
Cost is the second major driver. Aluminum is significantly cheaper per kilogram than copper. As EV production volumes scale into the millions, even a small per-vehicle cost saving becomes enormous across an entire model line. Aluminum busbars offer a cost-effective solution without compromising electrical performance.
Finally, aluminum provides sufficient conductivity for most EV busbar applications. Pure aluminum grades like 1060 and 1070 offer 61–62% IACS conductivity. While this is lower than copper’s 100% IACS, engineers compensate by using a slightly larger cross-sectional area. The weight and cost savings far outweigh the modest increase in cross-section needed.
Key point: Aluminum has become the dominant busbar material in modern EV battery packs. It offers 40–60% weight savings and significant cost reduction compared to copper, with sufficient conductivity for most applications. For high-current EV busbars, aluminum strip in 1060, 1070, or 3003 alloys is the industry standard.
Busbar Function in EV Battery Pack
Before selecting an aluminum alloy, it is important to understand what a busbar does in an EV battery pack. Busbars are rigid or semi-rigid conductive strips that connect battery cells in series or parallel. They serve three critical functions:
- Current collection and distribution — Busbars carry the combined current from hundreds or thousands of individual battery cells. During fast charging, currents can exceed 300A. During acceleration, discharge currents can be even higher.
- Voltage sensing — Many busbars include voltage sensing tabs or weld points. The battery management system (BMS) uses these to monitor individual cell voltages for safety and performance optimization.
- Structural support — In some pack designs, busbars also provide mechanical support for the cell array. They help maintain consistent cell spacing and alignment during vehicle vibration and thermal expansion.
Typical Operating Conditions
EV battery busbars operate under demanding conditions. Engineers must account for several variables:
| Parameter | Typical Range | Notes |
|---|---|---|
| Continuous current | 100 – 300 A | Depends on pack voltage and power rating |
| Peak discharge current | 300 – 800 A | During hard acceleration |
| Peak charge current (fast charging) | 200 – 500 A | DC fast charging at 150–350 kW |
| Operating temperature | -30 °C to +60 °C | Extreme climate conditions |
| Busbar temperature rise | ≤ 30 °C above ambient | Under continuous rated current |
| Typical thickness | 0.8 – 3.0 mm | Depends on current rating and alloy |
| Typical width | 20 – 200 mm | Module-level vs. pack-level busbars |
These operating conditions directly influence alloy selection. For example, a busbar that must carry 500A continuously needs a larger cross-section and higher conductivity alloy than one that carries only 100A. Similarly, a busbar in a structural role may need higher mechanical strength than a pure current-carrying busbar.
Alloy Selection: 1060 vs 1070 vs 3003 vs 6061
Four aluminum alloys dominate the EV busbar market: 1060, 1070, 3003, and 6061. Each has distinct properties. The right choice depends on your specific requirements for conductivity, strength, formability, and corrosion resistance.
Alloy Comparison Table
| Property | 1060 | 1070 | 3003 | 6061 |
|---|---|---|---|---|
| Aluminum purity | ≥ 99.60% | ≥ 99.70% | ~98.5% (with Mn) | ~97.9% (with Mg, Si) |
| Key alloying elements | None (pure Al) | None (pure Al) | Mn 1.0–1.5% | Mg 0.8–1.2%, Si 0.4–0.8% |
| Electrical conductivity (% IACS) | ≥ 61% | ≥ 62% | 40 – 50% | 40 – 45% |
| Thermal conductivity (W/m·K) | 234 | 238 | 163 | 167 |
| Tensile strength (annealed, MPa) | 70 – 95 | 70 – 95 | 110 – 145 | 120 – 150 (annealed) |
| Yield strength (annealed, MPa) | 25 – 45 | 25 – 45 | 40 – 60 | 55 – 80 (annealed) |
| Elongation (%) | 35 – 45% | 35 – 45% | 25 – 35% | 20 – 30% (annealed) |
| Formability | Excellent | Excellent | Good | Fair (annealed); Good (T4/T6) |
| Corrosion resistance | Excellent | Excellent | Very good | Good |
| Weldability | Excellent | Excellent | Excellent | Good (T4/T6) |
| Typical busbar use case | High-current, low-strength | Highest-current, premium | Medium-current, higher strength | Structural busbars |
1060 Aluminum: The Workhorse
1060 is the most widely used alloy for EV battery busbars. It offers a minimum of 99.60% aluminum purity. This high purity translates to excellent electrical conductivity (≥61% IACS) and thermal conductivity (234 W/m·K). In addition, 1060 has outstanding formability. It can undergo deep drawing, bending, and stamping without cracking. This makes it ideal for complex busbar geometries with multiple bends and tabs.
However, 1060 has relatively low mechanical strength. Its annealed tensile strength is only 70–95 MPa. Therefore, it is best suited for busbars where electrical conductivity is the primary requirement and structural loads are minimal. Most cell-level and module-level busbars use 1060.
1070 Aluminum: The Premium Choice
1070 is the highest-purity commercial aluminum alloy used for busbars, with a minimum of 99.70% aluminum. The extra 0.1% purity over 1060 may seem small, but it delivers measurable benefits. Specifically, 1070 offers slightly higher conductivity (≥62% IACS) and thermal conductivity (238 W/m·K). For high-power EV packs where every fraction of a percent in efficiency matters, 1070 is the premium choice.
Like 1060, 1070 has excellent formability and corrosion resistance. The main trade-off is cost. 1070 is typically 5–15% more expensive than 1060 due to the higher purity requirement. Therefore, engineers specify 1070 when the conductivity gain justifies the cost premium, such as in high-performance or long-range EV models.
3003 Aluminum: The Strength Upgrade
3003 is an aluminum-manganese alloy with 1.0–1.5% manganese. The manganese addition significantly improves mechanical strength. 3003 offers 110–145 MPa tensile strength in the annealed state — roughly 50% stronger than 1060. This makes 3003 suitable for busbars that must also carry structural loads or withstand vibration and mechanical stress.
The trade-off is conductivity. 3003 offers only 40–50% IACS conductivity, significantly lower than 1060 or 1070. Therefore, a 3003 busbar needs a larger cross-section to carry the same current as a 1060 busbar. Engineers choose 3003 when mechanical strength is more critical than maximum conductivity, or when the busbar design can accommodate a larger cross-section.
6061 Aluminum: The Structural Option
6061 is a magnesium-silicon alloy that can be heat-treated to high strength (T6 temper: 240–290 MPa tensile strength). It is widely used in structural applications. For EV busbars, 6061 is used when the busbar must serve a dual purpose: current carrying and structural support. For example, some pack designs use busbars as part of the module frame or cooling plate assembly.
However, 6061 has the lowest conductivity of the four alloys (40–45% IACS). It is also less formable in the T6 temper. Therefore, 6061 is a niche choice for EV busbars. Most manufacturers prefer 1060 or 1070 for pure current-carrying busbars, and 3003 when moderate strength is needed.
Alloy Selection Decision Guide
| Your Priority | Recommended Alloy | Reason |
|---|---|---|
| Maximum conductivity / minimum voltage drop | 1070 | Highest purity, ≥62% IACS |
| Best balance of conductivity and cost | 1060 | ≥61% IACS, widely available, cost-effective |
| Higher mechanical strength with good conductivity | 3003 | 50% stronger than 1060, still 40–50% IACS |
| Structural busbar with load-bearing requirements | 6061-T6 | Heat-treatable to high strength, but lower conductivity |
| Complex geometry with multiple bends | 1060 or 1070 | Excellent formability, low springback |
| Harsh / corrosive environment | 1060 or 1070 | Highest purity = best corrosion resistance |
| Ultrasonic welding to battery tabs | 1060 or 1070 | Soft, pure aluminum welds more reliably |
Electrical Conductivity Requirements
Electrical conductivity is the most critical property for an EV busbar. It determines how much voltage drop occurs across the busbar, how much heat is generated, and how efficiently the battery delivers power. Therefore, engineers must carefully calculate the required conductivity and cross-section.
Conductivity Standards
Aluminum conductivity is typically measured in % IACS (International Annealed Copper Standard). In this scale, pure annealed copper equals 100% IACS. For EV busbar aluminum strip:
- 1060: Minimum 61% IACS (typical 61–62%)
- 1070: Minimum 62% IACS (typical 62–63%)
- 3003: 40–50% IACS (depends on manganese content and temper)
- 6061: 40–45% IACS (depends on temper)
When sourcing aluminum strip for busbars, always specify the minimum conductivity requirement on the purchase order. Reputable suppliers, including Fullgreat, provide conductivity test results with each batch. The standard test method is ASTM E1004 (electromagnetic method) or the four-point probe method (ASTM B193).
Voltage Drop Calculation
The voltage drop across a busbar follows Ohm’s Law:
V = I × R
Where R (resistance) is calculated as:
R = ρ × L / A
And ρ (resistivity) is the inverse of conductivity:
ρ = 0.01724 / (% IACS / 100) Ω·mm²/m
For a 1060 aluminum busbar (61% IACS):
- ρ = 0.01724 / 0.61 = 0.02826 Ω·mm²/m
Example: A 1.5 mm thick × 50 mm wide × 1.0 m long 1060 busbar carrying 200A:
- Cross-section A = 1.5 × 50 = 75 mm²
- R = 0.02826 × 1.0 / 75 = 0.000377 Ω
- V = 200 × 0.000377 = 0.075 V (75 mV)
- Power loss = I² × R = 200² × 0.000377 = 15.1 W
As a general rule, busbar voltage drop should be kept below 50–100 mV per meter for most EV applications. If the calculated drop exceeds this, increase the cross-section by using thicker or wider strip, or switch to a higher-conductivity alloy.
Thermal Considerations
The power lost in the busbar converts to heat. This heat must be dissipated to prevent excessive temperature rise. In EV battery packs, busbars are often in direct contact with the cooling plate or surrounded by thermally conductive potting compound. Therefore, thermal conductivity is also important.
1060 aluminum offers 234 W/m·K thermal conductivity. This is about 59% of copper’s 401 W/m·K. However, because aluminum busbars are typically thicker than equivalent copper busbars, the actual heat dissipation can be comparable.
Mechanical Requirements for Busbar Stamping
EV busbars are not flat strips. They are complex stamped components with multiple bends, tabs, holes, and weld points. Therefore, the aluminum strip must have good stamping and forming properties. The key mechanical properties for stamping are yield strength, elongation, and springback.
Stamping Process for Busbars
Busbar manufacturing typically involves several stamping operations:
- Blanking — The busbar profile is cut from the strip using a blanking die. This creates the outer shape, including tabs and notches.
- Piercing — Holes for bolts, rivets, or sensor contacts are pierced.
- Bending / forming — The busbar is bent into its final 3D shape. This may include multiple bends at different angles, offsets, and embossments.
- Coining / embossing — Some busbars have coined areas for improved contact resistance or weldability.
Formability by Alloy
| Property | 1060 | 1070 | 3003 | 6061 (annealed) |
|---|---|---|---|---|
| Minimum bend radius (1x thickness) | 0.5t | 0.5t | 1.0t | 1.5t |
| Springback (relative) | Low | Low | Medium | High |
| Stretch formability | Excellent | Excellent | Good | Fair |
| Drawing depth (Limiting Draw Ratio) | 2.0–2.2 | 2.0–2.2 | 1.8–2.0 | 1.6–1.8 |
| Edge cracking tendency | Low | Low | Medium | Medium-High |
1060 and 1070 are the easiest alloys to stamp. Their low yield strength and high elongation allow tight bends (down to 0.5× thickness) without cracking. They also have low springback, which means the busbar retains its bent shape more accurately. This reduces the need for over-bending compensation in the die design.
3003 requires slightly larger bend radii (1.0× thickness minimum) and has more springback. However, its higher strength means the finished busbar better retains its shape under vibration and thermal cycling. 6061 in the annealed state is formable, but it has the highest springback and requires the largest bend radii. Most busbar manufacturers avoid 6061 unless structural strength is essential.
Temper Selection for Stamping
Aluminum strip temper also affects stamping performance:
- O (annealed): Softest, most formable. Best for complex busbars with multiple tight bends. Most EV busbars use O temper.
- H14 (half-hard): Moderate strength and formability. Used for busbars that need some rigidity but still require bending.
- H18 (full-hard): Maximum strength, minimal formability. Only used for simple flat busbars with no or minimal bending.
For most EV busbar applications, O temper (fully annealed) 1060 or 1070 is the standard choice. It provides the best combination of formability, conductivity, and cost.
Surface Treatment Options
The surface condition of an aluminum busbar affects its contact resistance, corrosion resistance, weldability, and appearance. Several surface treatment options are available. The right choice depends on the specific application requirements.
Bare (Untreated) Aluminum
Bare aluminum strip has a natural oxide layer (Al₂O₃) that forms immediately upon exposure to air. This oxide layer provides good corrosion resistance but has relatively high electrical contact resistance. For busbars that will be welded (ultrasonic or laser welding), bare aluminum is often preferred because the welding process breaks through the oxide layer.
However, for bolted or clamped connections, the oxide layer can cause high contact resistance and overheating. In these cases, a surface coating is recommended.
Tin Plating
Tin plating is the most common surface treatment for aluminum busbars. A thin layer of tin (typically 2–5 μm) is deposited on the aluminum surface. Tin offers:
- Low and stable contact resistance
- Good corrosion resistance
- Excellent solderability (if soldering is needed)
- Compatibility with copper and aluminum connections
Tin-plated aluminum busbars are widely used in EV battery packs. The tin layer ensures reliable electrical contact at bolted joints and reduces the risk of galvanic corrosion at aluminum-copper interfaces.
Nickel Plating
Nickel plating offers higher hardness and better wear resistance than tin. It is used for busbars that experience frequent mating/unmating or that operate in high-temperature environments. Nickel has higher contact resistance than tin, but it is more durable. Nickel plating is also used as an underlayer for other coatings or for improved ultrasonic weldability.
Anodizing
Anodizing creates a thick, hard aluminum oxide layer on the surface. It provides excellent corrosion resistance and electrical insulation. For busbars, anodizing is sometimes used on non-contact areas to prevent short circuits between adjacent busbars or between busbars and the pack housing. However, anodized areas must be masked or removed at contact points because the oxide layer is non-conductive.
Chemical Conversion Coating
Chemical conversion coatings (such as chromate or phosphate coatings) provide a thin, conductive layer that improves corrosion resistance and paint adhesion. They are sometimes used as a pre-treatment before painting or as a temporary protective layer during storage and transport.
Surface Treatment Selection Guide
| Application | Recommended Treatment | Reason |
|---|---|---|
| Ultrasonic / laser welded connections | Bare (untreated) | Welding penetrates oxide; coating can interfere |
| Bolted / clamped connections | Tin plated | Low stable contact resistance, corrosion protection |
| High-temperature / high-wear contacts | Nickel plated | Higher hardness, temperature resistance |
| Insulation between busbars | Anodized (non-contact areas) | Electrical insulation, corrosion resistance |
| General purpose, cost-sensitive | Bare or tin plated | Cost-effective, widely available |
Thickness & Width Specifications
Selecting the right thickness and width for an EV busbar requires balancing electrical, thermal, mechanical, and space constraints. Fullgreat supplies aluminum strip for busbars in the following range:
| Parameter | Range | Notes |
|---|---|---|
| Thickness | 0.5 – 3.0 mm | 0.8–2.0 mm is most common for EV busbars |
| Width | 10 – 600 mm | 20–150 mm is typical for module-level busbars |
| Thickness tolerance | ±0.02 mm (standard) / ±0.01 mm (precision) | Critical for consistent stamping die fit |
| Width tolerance | ±0.05 mm (standard) / ±0.02 mm (precision slitting) | Important for blanking die alignment |
| Edge condition | Slit edge (standard) / rounded / deburred | Rounded edges reduce stress concentration in bending |
| Camber | ≤ 1.5 mm / 1000 mm | Critical for high-speed stamping feed |
| Surface finish | Mill finish (standard) / bright / polished | Depends on coating and application requirements |
| Temper | O (annealed) / H14 / H18 | O temper is standard for busbar stamping |
| Coil ID | 508 mm (20″) standard / 305 mm (12″) on request | Must match stamping press decoiler |
| Coil weight | Up to 5,000 kg | Longer coils reduce coil change downtime |
Thickness Selection by Current Rating
As a starting point for 1060 aluminum busbars (O temper, natural convection cooling):
| Continuous Current | Recommended Thickness | Typical Width Range | Approx. Temperature Rise |
|---|---|---|---|
| ≤ 100 A | 0.8 – 1.0 mm | 20 – 40 mm | ≤ 15 °C |
| 100 – 200 A | 1.0 – 1.5 mm | 30 – 60 mm | ≤ 20 °C |
| 200 – 300 A | 1.5 – 2.0 mm | 40 – 80 mm | ≤ 25 °C |
| 300 – 500 A | 2.0 – 3.0 mm | 60 – 120 mm | ≤ 30 °C |
| > 500 A | 3.0 mm+ or multiple busbars | 80 – 200 mm | Requires active cooling analysis |
Note: These are starting estimates only. Actual busbar sizing requires detailed electro-thermal simulation considering ambient temperature, cooling method, enclosure, duty cycle, and maximum allowable temperature rise. Always verify with Finite Element Analysis (FEA) or physical testing.
Fullgreat’s EV Busbar Aluminum Strip Capability
Fullgreat Metal supplies precision aluminum strip for EV battery busbar applications. Our capabilities include:
| Capability | Details |
|---|---|
| Alloys | 1060, 1070, 1050, 3003, 5052, 5083, 6061 |
| Thickness range | 0.2 – 6.0 mm (0.5 – 3.0 mm for busbar standard) |
| Width range | 10 – 600 mm (precision slitting to custom widths) |
| Temper | O (annealed), H12, H14, H16, H18, H24, H32 |
| Conductivity (1060/1070) | ≥ 61% IACS (1060), ≥ 62% IACS (1070), certified per batch |
| Surface treatment | Mill finish, tin plating, nickel plating, anodizing (via qualified partners) |
| Edge condition | Slit edge, rounded edge, deburred edge |
| Precision slitting | Minimum width 3 mm, width tolerance ±0.01 mm |
| Coil weight | Up to 5,000 kg, coil ID 508 mm / 305 mm / 610 mm |
| Packaging | Waterproof paper + VCI film + wooden pallet / steel crate, export standard |
| Certification | EN 10204 3.1 MTC per batch, conductivity test report, third-party inspection (SGS, BV, TÜV) available |
| Custom development | Custom alloys, tempers, dimensions, and surface treatments for specific EV programs |
Fullgreat’s aluminum strip production includes in-house precision slitting, edge conditioning, and tension leveling. We work with EV manufacturers, Tier 1 suppliers, and busbar stamping companies worldwide. Our quality system ensures consistent conductivity, flatness, and dimensional tolerance across every coil.
Quality Control & Testing
For EV busbar applications, quality control is critical. A single defective busbar can cause a battery pack failure, safety recall, or warranty claim. Fullgreat implements rigorous quality control at every stage of production:
Incoming Material Inspection
- Chemical composition verification via optical emission spectrometry (OES)
- Conductivity testing (eddy current method, ASTM E1004)
- Surface quality inspection for scratches, pits, and roll marks
- Thickness and width verification with micrometers and calipers
In-Process Quality Control
- Continuous thickness monitoring during rolling
- Width verification after slitting
- Edge quality inspection (burr height, edge crack)
- Flatness measurement (tension leveling verification)
- Surface inspection at every processing step
Final Testing & Certification
- Tensile test (ASTM E8 / EN ISO 6892) — tensile strength, yield strength, elongation
- Hardness test (Vickers / Rockwell / Brinell)
- Conductivity test (eddy current, % IACS)
- Bend test (180° bend, verify no cracking)
- Microstructure examination (grain size, intermetallic particles)
- Surface roughness (Ra measurement)
- Dimensional report (thickness, width, camber, flatness)
Every batch ships with an EN 10204 Type 3.1 Mill Test Certificate documenting all test results. For critical EV programs, we can also arrange third-party inspection by SGS, Bureau Veritas, or TÜV Rheinland.
Frequently Asked Questions
Q: Why is aluminum used for EV busbars instead of copper?
A: Aluminum offers 40–60% weight savings compared to copper. In an EV, this directly improves range. Aluminum is also significantly cheaper per kilogram. While aluminum has lower conductivity (61–62% IACS vs. copper’s 100% IACS), engineers compensate by using a slightly larger cross-section. The weight and cost savings far outweigh the modest increase in cross-section needed. Today, aluminum is the dominant busbar material in most EV battery packs.
Q: Which aluminum alloy is best for EV busbars?
A: For most EV busbar applications, 1060 aluminum is the standard choice. It offers ≥61% IACS conductivity, excellent formability, and good corrosion resistance at a competitive price. For high-performance models where maximum conductivity is critical, 1070 (≥62% IACS) is the premium upgrade. For busbars that need higher mechanical strength, 3003 is a good option, though it has lower conductivity (40–50% IACS). 6061 is used only for structural busbars where load-bearing is essential.
Q: What thickness of aluminum strip do I need for my busbar?
A: Thickness depends on the continuous current rating. As a starting point for 1060 aluminum: ≤100A use 0.8–1.0mm, 100–200A use 1.0–1.5mm, 200–300A use 1.5–2.0mm, 300–500A use 2.0–3.0mm. However, these are estimates only. Actual sizing requires detailed electro-thermal simulation considering cooling method, ambient temperature, duty cycle, and maximum allowable temperature rise. Always verify with FEA or physical testing.
Q: Do I need tin plating on my aluminum busbar?
A: It depends on the connection type. For ultrasonic or laser welded connections, bare aluminum is usually preferred because the welding process breaks through the natural oxide layer. For bolted or clamped connections, tin plating is strongly recommended. Tin provides low and stable contact resistance, good corrosion protection, and reduces galvanic corrosion risk at aluminum-copper interfaces. Most EV busbars use tin plating (2–5 μm) on contact areas.
Q: What temper should I specify for busbar stamping?
A: For most busbar stamping applications, O temper (fully annealed) is the standard choice. O temper offers the best formability, allowing tight bends (down to 0.5× thickness) without cracking. It also has low springback, which simplifies die design. H14 (half-hard) is used for busbars that need some rigidity but still require bending. H18 (full-hard) is only used for simple flat busbars with no or minimal bending.
Q: Can you supply custom widths and small trial quantities?
A: Yes. Fullgreat offers precision slitting to custom widths from 3 mm to 600 mm, with width tolerances as tight as ±0.01 mm. We support trial orders for sample validation and prototype development. For volume production, we offer monthly supply contracts with consistent quality and just-in-time delivery. Contact our engineering team with your specifications for a quotation.
Need precision aluminum strip for EV battery busbars? Choose from 1060, 1070, 3003, or custom alloys with certified conductivity (≥61% IACS), precision slitting, and tin/nickel plating options. Request a quote → or contact our engineering team at Bruce@fullgreat.com. Sample coils available for stamping and conductivity validation before bulk orders.
